这篇文章给大家介绍了“Centos服务器通过vsftpd搭建FTP”的相关知识，讲解详细，步骤过程清晰，有一定的借鉴学习价值，因此分享给大家做个参考，感兴趣的朋友接下来一起跟随小编看看吧。

Centos 7.2 FTP服务器的启动配置

一、安装vsftpd

yum -y install vsftpd 

二、启动服务器

service vsftpd start

三、编辑vsftpd服务器配置文件

vi /etc/vsftpd/vsftpd.conf

# Example config file /etc/vsftpd/vsftpd.conf
#
# 匿名用户登录ftp服务使能
anonymous_enable=YES
#
# Uncomment this to allow local users to log in.
# 本地用户登录ftp服务使能
local_enable=YES
#
# 本地用户写权限使能
write_enable=YES
# 允许用户的主目录具有写权限
allow_writeable_chroot=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
local_umask=022
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
# When SELinux is enforcing check for SE bool allow_ftpd_anon_write, allow_ftpd_full_access
#anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
#
# Activate logging of uploads/downloads.
xferlog_enable=YES
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#chown_uploads=YES
#chown_username=whoever
#
# You may override where the log file goes if you like. The default is shown
# below.
#xferlog_file=/var/log/xferlog
#
# If you want, you can have your log file in standard ftpd xferlog format.
# Note that the default log file location is /var/log/xferlog in this case.
xferlog_std_format=YES
#
# You may change the default value for timing out an idle session.
#idle_session_timeout=600
#
# You may change the default value for timing out a data connection.
#data_connection_timeout=120
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#nopriv_user=ftpsecure
#
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that on some FTP servers, ASCII support allows a denial of service
# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
# predicted this attack and has always been safe, reporting the size of the
# raw file.
# ASCII mangling is a horrible feature of the protocol.
#ascii_upload_enable=YES
#ascii_download_enable=YES
#
# You may fully customise the login banner string:
#ftpd_banner=Welcome to blah FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
# (default follows)
#banned_email_file=/etc/vsftpd/banned_emails
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
# 限制用户只能在用户主目录下
chroot_local_user=YES
# 限制用户除列表以外用户，与chroot_local_user配合使用
#chroot_list_enable=YES
# 列表文件所在路径
#chroot_list_file=/etc/vsftpd/chroot_list
# 匿名登录目录
anon_root=/var/ftp/anoner
# 匿名登录禁止上传
anon_upload_enable=NO
# 匿名登录只读
anon_world_readable_only=YES
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#ls_recurse_enable=YES
#
# When "listen" directive is enabled, vsftpd runs in standalone mode and
# listens on IPv4 sockets. This directive cannot be used in conjunction
# with the listen_ipv6 directive.
listen=NO
#
# This directive enables listening on IPv6 sockets. By default, listening
# on the IPv6 "any" address (::) will accept connections from both IPv6
# and IPv4 clients. It is not necessary to listen on *both* IPv4 and IPv6
# sockets. If you want that (perhaps because you want to listen on specific
# addresses) then you must run two copies of vsftpd with two configuration
# files.
# Make sure, that one of the listen options is commented !!
listen_ipv6=YES

pam_service_name=vsftpd
userlist_enable=YES
tcp_wrappers=YES

service vsftpd restart

四、添加ftp用户并修改密码

useradd UserFtp -s /sbin/nologin -d /var/ftp/userftp
passwd UserFtp

由此ftp服务器就可以匿名登录和用户登录了，用户登录具有读写权限和上传下载功能，匿名登录只有读权限和下载功能。

关于“Centos服务器通过vsftpd搭建FTP”的内容今天就到这，感谢各位的阅读，大家可以动手实际看看，对大家加深理解更有帮助哦。如果想了解更多相关内容的文章，关注我们，群英网络小编每天都会为大家更新不同的知识。

免责声明：本站发布的内容（图片、视频和文字）以原创、转载和分享为主，文章观点不代表本网站立场，如果涉及侵权请联系站长邮箱：mmqy2019@163.com进行举报，并提供相关证据，查实之后，将立刻删除涉嫌侵权内容。

猜你喜欢

• Linux中ls命令的作用及详细用法是怎样的

  在linux中，ls命令显示的蓝色表示“目录”。ls命令会根据文件的具体类型给文件名配色：1、白色表示普通文件；2、亮绿色表示可执行文件；3、亮红色表示压缩文件；4、蓝色表示目录；5、亮蓝色表示链接文件；6、亮黄色表示设备文件。

• Linux查看错误日志的命令是什么，具体怎么用

  在linux中，可以利用tail命令查看错误日志，该命令用于查看文件的内容，语法为“tail -f /var/log/messages”；参数“-f”表示把文件里的最尾部的内容显示在屏幕上，并且不断刷新，“/var/log/message”文件是系统启动后的信息和错误日志。

• Linux中如何查看负载，命令是什么

  linux负载查看的命令是：1、【top】命令查看linux负载；2、【uptime】命令查看linux负载；3、【w】命令查看linux负载；4、【vmstat】命令查看linux负载。

• Linux下esc退出vi编辑器没用的情况如何解决

  linux中退出vi编辑器，按下esc没反应的解决办法：1、在正常模式下按下q键盘；2、选择【a-z】或【0-9】中任意一个作为缓冲器的名字，准备开始录制宏；3、在非insert模式下输入q停止宏的录制；4、使用@和定义的缓冲器名字即可。

• linux下su和sudo命令如何使用？

  linux下su和sudo命令如何使用？本篇文章今天主要给大家着重介绍下linux系统的su和sudo命令的相关资料，对此有疑惑的小伙伴可以跟随小编来看一看，希望这篇文章能帮助到你们。